Three Iron
Problem is, the VR6's were all 5 doors, and mine is a 3 door. The seats don't adjust far enough forward, so a flipping mechanism was needed to let rear seat passengers enter and egress. I didn't think that VW would tool up 2 different sorts of seat mechanisms for the small volume of 3 doors, so I went searching for clues on how to convert the new seats to flippers....
Pulled off the adjusting knob and plastic cover to reveal this. Got curious about the big screw, so I undid it.
Which enabled this little tab to be flipped back, which freed the seat on the outboard side.
Then, all you do is move the latch up on the inboard side, and voila, flipping seats!
Pulled off the adjusting knob and plastic cover to reveal this. Got curious about the big screw, so I undid it.
Which enabled this little tab to be flipped back, which freed the seat on the outboard side.
Then, all you do is move the latch up on the inboard side, and voila, flipping seats!
The bar for child restraints is not meant to be removable on these cars, and they're secured by some sort of blind bolt. The child restraint bar is not structural, and really eats into the cargo area, so I hacksawed it off to put my bike in the boot.
Got another bar from Tonz with the interior, so I figured it was time to make a proper removable bar. Filed down the bolts to create a sort of slot that I could use an 8mm spanner on. The bolt was made from really soft metal, so it was really hard to get it off without stripping my makeshift bolt head. But I got there!
Got another bar from Tonz with the interior, so I figured it was time to make a proper removable bar. Filed down the bolts to create a sort of slot that I could use an 8mm spanner on. The bolt was made from really soft metal, so it was really hard to get it off without stripping my makeshift bolt head. But I got there!
- type3disease
- KING KOMBI
- Posts: 9656
- Joined: Sun Aug 05, 2007 3:58 pm
- Location: Dak-Dak Cafe
- Tonz Magonz
- Postal Spammer
- Posts: 6776
- Joined: Mon Aug 06, 2007 9:56 pm
- Location: W2 and smiling like an idiot
Nafe wrote:Next thing will be to give the interior a good scrub, it looks like both the driver and passenger have both spilt chocolate milkshake on the seats.... And hopefully I can sell my old interior!
That ain't chocolate milk mate....
Spend the money you saved on the seats and get them steam cleaned..
Can't recommend highly enough, the services of Peter Swanson..( long term dubber )
He details cars and cleaned some serious staining from the front seats of my T5..
Couldn't believe how good they came up...
Shoot me a pm and I'll get you his number...
Looking for a mk3 VR6 and a 90's hiace... Future projects for shits and giggles.
Thanks mate!Tonz Magonz wrote:Nafe wrote:Next thing will be to give the interior a good scrub, it looks like both the driver and passenger have both spilt chocolate milkshake on the seats.... And hopefully I can sell my old interior!
That ain't chocolate milk mate....
Spend the money you saved on the seats and get them steam cleaned..
Can't recommend highly enough, the services of Peter Swanson..( long term dubber )
He details cars and cleaned some serious staining from the front seats of my T5..
Couldn't believe how good they came up...
Shoot me a pm and I'll get you his number...
I think I have one of his business cards floating around, but if I can't find it I'll shoot you a PM
And you really should be more careful with your 'chocolate milk'.
- Tonz Magonz
- Postal Spammer
- Posts: 6776
- Joined: Mon Aug 06, 2007 9:56 pm
- Location: W2 and smiling like an idiot
Not mine ...Nafe wrote:Thanks mate!Tonz Magonz wrote:Nafe wrote:Next thing will be to give the interior a good scrub, it looks like both the driver and passenger have both spilt chocolate milkshake on the seats.... And hopefully I can sell my old interior!
That ain't chocolate milk mate....
Spend the money you saved on the seats and get them steam cleaned..
Can't recommend highly enough, the services of Peter Swanson..( long term dubber )
He details cars and cleaned some serious staining from the front seats of my T5..
Couldn't believe how good they came up...
Shoot me a pm and I'll get you his number...
I think I have one of his business cards floating around, but if I can't find it I'll shoot you a PM
And you really should be more careful with your 'chocolate milk'.
More likely is the gun residue from the previous owner...
Marcia Hines
Looking for a mk3 VR6 and a 90's hiace... Future projects for shits and giggles.
Just like the MK1, the oilpan sits really low on the MK3. For my mk1, I put an oilpan on that was reinfoeced with 1/4in steel plate. Which stopped any dents when I hit it, but it was then 1/4in closer to the ground, and instead of blowing oilpans, I chewed through CV joints.
So, it was back to the drawing board when it came time to lower the mk3. I used 20mm billet engine & trans mount spacers, bringing the oilpan well out of trouble, and correcting the angle of the CVs.
However, I'm still undecided about this method, as the engine is no longer exactly where it is meant to be. I'll leave them in for R&D purposes, and decide how I feel after a few 1000 k's.
Although the driveshafts are on a much better angle, they're also now closer to the body, and at the height shown above, I was getting shaft to body contact.
So, it was back to the drawing board when it came time to lower the mk3. I used 20mm billet engine & trans mount spacers, bringing the oilpan well out of trouble, and correcting the angle of the CVs.
However, I'm still undecided about this method, as the engine is no longer exactly where it is meant to be. I'll leave them in for R&D purposes, and decide how I feel after a few 1000 k's.
Although the driveshafts are on a much better angle, they're also now closer to the body, and at the height shown above, I was getting shaft to body contact.
So unfortunately, it had to be raised. I might entertain the thought of a frame notch later down the track? But for the moment, this is still my daily, and I should probably be restrained.
I got a nail in my tyre the other week, and was offered some D90's for a very good price. I thought this was serendipitous, and jumped at the offer.
I did a dummy fit today, and got the rideheight lifted, with a Fender to Ground measurement of 595mm all round, where it was previously 555mm. I think the best height would be about 580mm, as the 195/45s have a diameter of 582mm. However, this will wait until I roll the guards.
Anyway, enough words.
I got a nail in my tyre the other week, and was offered some D90's for a very good price. I thought this was serendipitous, and jumped at the offer.
I did a dummy fit today, and got the rideheight lifted, with a Fender to Ground measurement of 595mm all round, where it was previously 555mm. I think the best height would be about 580mm, as the 195/45s have a diameter of 582mm. However, this will wait until I roll the guards.
Anyway, enough words.